Chauvin Arnoux Make B102 Clamp
The B102 clamp is designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currents
on power circuits.
• Differential or leakage current, from 500 µA
• Currents up to 400 A max
• 2 measurement ranges: 1 mV/mA or 1 mV/A
• Used on single or multi-phase systems, with phased or unphased currents and on balanced or unbalanced circuits
• 110 mm jaw opening
• Measurement of fault currents on 3-wire 3-phase circuits without a neutral using an artificial neutral system
Chauvin Arnoux Make C173 Clamp
The C Series is a range of high-performance 1,000 A transformer clamps. The round jaw shape and the uniformly-distributed winding guarantee accuracy and minimum phase difference.
It is equipped with an oscillating magnetic element adjustment system and a patented system for gradual assisted jaw opening.
Its Ø 52 mm clamping capacity allows current measurements on most conductors on CAT III 600 V industrial and tertiary installations.
When used with a multimeter with an mV AC range and good measurement resolution, this 4-calibre clamp allows measurement of leakage or differential currents starting at 1 mA.
Main features
• Output signal: AC voltage
• Output / input ratio: 1 V / A AC, 100 mV / A AC, 10 mV / A AC, 1 mV / A AC,
• Output via lead and isolated Ø 4 mm male plugs
Chauvin Arnoux Make K1 Clamp for mA Measurements
The K Series is a range of "micro-clamps" for accurate measurements of very low direct and alternating currents.
Their small size and their shape make them ideal for exploring and measuring in places where access is difficult.
Main features
• Rated current: 3 A AC / 4.5 A DC
• Output signal: DC and AC current
• Output / input ratio: 1 mV / mA
• Output via isolated Ø4mm male plugs with 19 mm spacing
Chauvin Arnoux Make K2 Clamp for measurements on 4-20 mA Loops
The K Series is a range of "micro-clamps" for accurate measurements of very low direct and alternating currents.
Their small size and their shape make them ideal for exploring and measuring in places where access is difficult.
Main features of the K2 model
• Rated current: 300 mA AC / 450 mA DC
• Output signal: DC and AC current
• Output / input ratio: 10 mV / mA
• Output via isolated Ø4mm male plugs with 19 mm spacing
Chauvin Arnoux Make MN 71 Clamp for Measuring Alternating Currents
The MN Series is a range of versatile transformer clamps for measuring alternating currents up to 240 A with a multimeter or a power analyser.
Compact and ergonomic, the jaw is suitable for measurements in places where access is difficult and can also be used to clamp any cable up to 20 mm in diameter in installations up to CAT III 600 V or CAT IV 300 V.
The MN71 clamp has been developed in particular for current measurements on the secondary windings of current transformers.
Main features of the MN71 model
• Rated current: 10 A AC
• Output signal: AC voltage
• Output / input ratio: 100 mV / A AC
• Output via lead and isolated Ø 4 mm male plugs
Chauvin Arnoux Make MN73 High Sensitivity Clamp for Leakage Current
The MN Series is a range of versatile transformer clamps for measuring alternating currents up to 240 A with a multimeter or a power analyser.
Compact and ergonomic, the jaw is suitable for measurements in places where access is difficult and can also be used to clamp any cable up to 20 mm in diameter in installations up to CAT III 600 V or CAT IV 300 V.
When used with a multimeter equipped with an mV AC range and good measurement resolution, this 2-calibre clamp allows measurement of leakage or differential currents from 10 mA.
Main features of the MN73 model
• Output signal: AC voltage
• Output / input ratio: 1,000 mV / A AC, 10 mV / A AC
• Output via lead and isolated Ø 4 mm male plugs
