Cyronics - Industrial Division

 
IDRC

irdc make dc power supply dsp hp

IDRC Make DSP-HP Series Programmable DC Power Supply

Features

•    Up to 70 models, 16V~1000V / 40A~5000A / 40kW~160kW, are available for selection.
•    Up to 5 units in parallel (800kW) and 2 units in series.
•    Max. current 25000A in parallel.
•    Constant voltage / constant current with automatic crossover.
•    Optional constant power function.
•    IDRC DSP Series Programmable DC power supply uses digitalized design :

o    High resolution of D/A (16 bits)setting output voltage & current,
o    High resolution of A/D (24 bits H.W.) measurement output voltage & current.

•    True Watt and True RMS current measurement.
•    Complete Protection : OVP, OCP,OTP, Reversed polarity protection.
•    Definable output voltage ramp up and down with adjustable time.
•    DSP-HP Series can store 20 sets of memories, can be recalled manually in front panel.
•    4500 sets of sequence memories: it can store parameters of Voltage, current and time in every set and operate in order.
•    Last Panel Set.
•    KEY LOCK setting.
•    Embedded 3 RISC micro-controllers.
•    Built-in remote sensing with max. 5V compensation.
•    Digital Encoder Knobs, Pushbutton Settings.
•    Standard GPIB and Isolation RS-485 Interface.
•    RS-485 baud rate up to 57600 bps.
•    GPIB are compatible with SCPI.
•    Analog Programming and monitoring, isolated type is available for optional selection.
•    Modularized design to shorten lead time and improve reliability.
•    Speed-Controlled Fan
•    DC output ON / OFF switch.
•    Emergency stop switch.

irdc make dc power supply dsp hr

IDRC Make DSP-HR Series Switching Programmable DC Power Supply

Features

•    Up to 52 models: 6V~600V/1A~400A are available for selection.
•    5 digits of current and voltage meter.
•    Max. output current up to 2000A (5 units in parallel).
•    Switching mode, high density, and convenience for installation to 19” rack,
•    750W in 1U half width, 1.5kW in 1U/2UH, 3kW in 2U height.
•    Non-gap stacking, no ventilation holes at the cover and bottom plate of the power supply.
•    Universal Input Voltage
               1U / 1UH / 2UH :100-240Vac,50/60Hz, 1P2W+GND continuous operation.
               2U :190-240Vac,50/60Hz, 1P2W+GND continuous operation.
•    Constant Voltage / Constant Current with automatic crossover.
•    IDRC DSP Series 1U Programmable DC Power Supply uses digitalized design :
o    High resolution of D/A (16 bits)setting output Voltage & Current,
o    High resolution of A/D (24 bits H.W.) measurement output Voltage & Current.
•    Up to 5 units in parallel and 2 units in series, equipped with active current sharing.
•    Active power factor correction.
•    Complete Protection : OVP, OCP,OTP.
•    Definable output voltage ramp up and down with adjustable time.
•    DSP-HR Series can store 16 sets of memories; memories can be recalled manually in front panel or by external recall control.
•    Last setting retainable upon next power on.
•    KEY LOCK setting.
•    Embedded 3 RISC Micro-Controllers.
•    Built-in remote sensing with max. 5V compensation
•    Standard LXI and Isolation RS-485 Interface, optional GPIB interface.
•    RS-485 baud rate up to 115200 bps
•    GPIB are compatible with SCPI.
•    Analog Programming and Monitoring.
•    Modularized design to shorten lead time and improve reliability.
•    Speed-Controlled Fan
•    DC Output ON / OFF Switch.
•    LXI approved
•    CE approved

irdc make dc power supply dsp hd

IDRC Make DSP-HD Series Switching Programmable DC Power Supply

Features

•    Up to 52 models, 6V ~ 600V / 1A ~ 400A, are available for selection.
•    Switching mode, high density, and convenience for installation to 19” rack,
•    Max. output current up to 2000A (5 units in parallel).
•    750W in 1U half width, 1.5kW in 1U/2UH, 3kW in 2U height.
•    Non-gap stacking, no ventilation holes at the cover and bottom plate of the power supply.
•    Universal Input Voltage

1U / 1UH / 2UH :100-240Vac,50/60Hz, 1P2W+GND continuous operation.
2U :190-240Vac,50/60Hz, 1P2W+GND continuous operation.

•    Constant Voltage / Constant Current with automatic crossover.
•    IDRC DSP Series 1U Programmable DC Power Supply uses digitalized design :

o    High resolution of D/A (16 bits)setting output Voltage & Current,
o    High resolution of A/D (24 bits H.W.) measurement output Voltage & Current.

•    Up to 5 units in parallel and 2 units in series, equipped with active current sharing.
•    Active power factor correction.
•    Complete Protection : OVP, OCP,OTP.
•    Definable output voltage ramp up and down with adjustable time.
•    DSP-HD Series can store 16 sets of memories; memories can be recalled manually in front panel or by external recall control.
•    Last setting retainable upon next power on.
•    KEY LOCK setting.
•    Embedded 3 RISC Micro-Controllers.
•    Built-in remote sensing with max. 5V compensation
•    RS-485 baud rate up to 115200 bps
•    Standard LXI and Isolation RS-485 Interface, optional GPIB interface.
•    GPIB are compatible with SCPI.
•    Analog Programming and Monitoring.
•    Modularized design to shorten lead time and improve reliability.
•    Speed-Controlled Fan
•    DC Output ON / OFF Switch.
•    LXI approved
•    CE approved


Programmable DC Power Supply


no image

SYSKON P500  
SYSKON P800  
SYSKON P1500  
SYSKON P3000
SYSKON P4500

The innovative new SYSKON series of KONSTANTER power supplies provides you with top quality, programable and manual and remote controllable DC power supplies for laboratory and system use. Equipped with active power-factor control (PFC), it supplies 500 through 4500 W of power at up to 60 V and max. 180 A with characteristic UIP curve.

syscon graph

Special switching controller technology and matching status controllers assure high dynamics and short response times. The setting range for output voltage and output current can be restricted by specifying setting limits.

The analog interface is equipped with two programmable trigger inputs and three signal outputs, which can be linked to various device functions for indication, or for controlling external devices and an auxiliary power output. Beyond this, monitor outputs and control inputs for voltage and current setpoints are available as well. Sensing leads allow for auto-sensing operation at the power consumer. Strict menu-driven operation supports highly diverse programming functions. The device is transformed into a freely programmable test signal generator by means of an expanded sequence memory and extra functions.

Features & Highlights

  • Mains power input with power factor control (PFC)
  • Highly efficient, low power loss
  • Auto-ranging output with 500, 800, 1500, 3000 and 4500 W of power
  • Output: voltage and current regulated
  • Characteristic UIP curve
  • Very short response times
  • Excellent dynamic control parameters
  • Minimal residual ripple
  • Output on/off function
  • Comprehensive calibration report
  • Dynamic sink mode operation
  • Lockable controls
  • Master-slave operation for parallel and series connection
  • Sequence functions with sequence control for creating voltage and current sequences
  • Overvoltage, overcurrent and overtemperature protection
  • Calibrating procedure for menu-driven balancing
  • USB and RS 232 interfaces (complete control of the device)
  • Floating output terminals on the rear panel
  • Analog interface (extended)
  • Dimensions SYSKON P500, P800, P1500
  • Benchtop device: 447 x 102 (88 without feet) x 541 (501 without handles) mm 
  • 19" rack device: 19" x 2 standard height units x 501 mm
  • Dimensions SYSKON P3000, P4500
  • Benchtop device: 447 x 102 (88 without feet) x 541 (501 without handles) mm 
  • 19" rack device: 19" x 4 standard height units x 501 mm

Optional:

  • IEEE488 interface (with measured value querying)
  • Driver software for LabVIEW, LabWindows and HP VEE
  • Power line for P3000 and P4500

syscon table

Power Supplies & Electrical Load

Get Quote

About Us

At CIPL, we express who we are, through our Guiding Principles, Mission, Core Values and Objectives. Developed over time, each represent philosophy or goal that is intrinsically important to the organization. We invite you to explore these four ways of understanding CIPL as an organisation.

Contact Us

Cyronics Instruments Pvt Ltd.

CORPORATE OFFICE :
#11, Electronic Co-operative Estate,
Pune – Satara Road,
Pune 411009.
Maharashtra, INDIA
Boardline    :   +91 20-24208200
Faxline       :   +91 20-24208202

icon facebookicon twittericon linkedinicon googleplus